Model not solving
#9
(27-06-2019, 06:17 PM)Antti-L Wrote: Big models tend to call for some additional meticulousness in the modelling process.
I tested the run with all the Subreses listed below, by following my earlier advice, plus making small additional fine-tuning:
$BATINCLUDE elcconventionaltechs.dd
$BATINCLUDE elcrenewabletechs.dd
$BATINCLUDE backupboilers.dd
$BATINCLUDE centralised_alk_industry.dd
$BATINCLUDE centralised_alk_mobility.dd
$BATINCLUDE centralised_pem_industry.dd
$BATINCLUDE centralised_pem_mobility.dd
$BATINCLUDE centralised_pipeline_industry.dd
$BATINCLUDE centralised_pipeline_mobility.dd
$BATINCLUDE centralised_smr_industry.dd
$BATINCLUDE centralised_smr_mobility.dd
$BATINCLUDE centralised_tubetrailer_mobility.dd
$BATINCLUDE decentralised_alk_industry.dd
$BATINCLUDE decentralised_alk_mobility.dd
$BATINCLUDE decentralised_pem_industry.dd
$BATINCLUDE decentralised_pem_mobility.dd
$BATINCLUDE decentralised_smr_industry.dd
$BATINCLUDE decentralised_smr_mobility.dd

The resulting model had 1,595,487 equations, and the run solved quite nicely, in less than 500 seconds (about 8 minutes), see below the console output after crossover:


I see you have abandoned my suggestion for bounding the outflow of the storage in each timeslice by using FLO_SHAR, which you said you will incorporate.  May I ask why did you not incorporate it, but changed all storage to be AFC-based?
Dear Antti,

In this file, did you see dummy imports in the year 2017 and 2018 for the commodities HYGNINDfscap and HYGNINDfsmer? For me, there are dummy imports despite of having enough capacity. I do not understand why this is happening. In my model, the existing technologies capacity are defined as 'STOCK' (I had mentioned this in another post). But same STOCK value has been kept till the end of its lifetime. In my current model, I kept the same stock values which are actually sufficient to meet the demand in 2017 and 2018. However, the model is still importing. Instead of STOCK, I tried NCAP_PASTI and then the model is taking the capacity. Unfortunately, now If I change this to NCAP_PASTI instead of STOCK I will have to make lot of changes in my subRES files. Could you tell me why this could be happening?

Regards
Abi Afthab
Reply


Messages In This Thread
Model not solving - by MohammedAbiAfthab - 25-06-2019, 05:54 PM
RE: Model not solving - by Antti-L - 26-06-2019, 08:05 PM
RE: Model not solving - by MohammedAbiAfthab - 26-06-2019, 08:30 PM
RE: Model not solving - by MohammedAbiAfthab - 27-06-2019, 12:35 AM
RE: Model not solving - by MohammedAbiAfthab - 27-06-2019, 04:54 AM
RE: Model not solving - by Antti-L - 27-06-2019, 06:17 PM
RE: Model not solving - by MohammedAbiAfthab - 27-06-2019, 06:38 PM
RE: Model not solving - by MohammedAbiAfthab - 28-06-2019, 07:32 PM
RE: Model not solving - by Antti-L - 29-06-2019, 11:46 PM
RE: Model not solving - by MohammedAbiAfthab - 30-06-2019, 01:11 AM
RE: Model not solving - by Antti-L - 30-06-2019, 05:03 AM
RE: Model not solving - by MohammedAbiAfthab - 30-06-2019, 05:13 AM
RE: Model not solving - by MohammedAbiAfthab - 30-06-2019, 01:08 PM
RE: Model not solving - by MohammedAbiAfthab - 27-06-2019, 06:53 PM
RE: Model not solving - by Antti-L - 29-06-2019, 10:18 PM
RE: Model not solving - by Antti-L - 30-06-2019, 06:38 PM
RE: Model not solving - by MohammedAbiAfthab - 01-07-2019, 03:24 PM
RE: Model not solving - by MohammedAbiAfthab - 01-07-2019, 06:20 PM
RE: Model not solving - by MohammedAbiAfthab - 04-07-2019, 12:14 PM
RE: Model not solving - by MohammedAbiAfthab - 07-07-2019, 12:46 AM

Forum Jump:


Users browsing this thread: 1 Guest(s)